How Does UV Light Effect Finish, Which Style of Workbench, Sanding Tips and MORE!

Guys Questions:

Hey gentlemen, welcome Brian. I have a commission for a big walnut slab table that will live in a nook with windows on 3 sides (lots of UV exposure). What do you recommend for finishing. I seem to recall Guy mentioning some walnut finishes don’t hold up well to UV exposure. I’m probably a month out from delivery so hopefully this makes it to the show before then! Sincerely your accidentental woodworking fabricator. Will

In the past I’ve done a few small veneering projects and am currently working on one which will require a few larger panels- about 24”x 31”. Previously I used a train-load of clamps and cauls to press the veneer but now I want to step up my game so I ordered a vacuum press. Thanks to a few of Guy’s videos the process seems pretty straightforward but I do have a question on the glue. For veneering my only experience is with Titebond cold press veneer glue with good results but in some videos I’ve seen some folks recommend Urea-formaldehyde glue - especially for larger panels. Do any of you have experience with this stuff? Sounds a bit nasty but if it’s better for the application I’ll give it a shot. Thanks! Jeffrey

Brians Questions:

Been listening to the podcast for a couple years now, and while I'm sorry to see Sean step away for now, I'm happy that you found someone willing to chip in! Two things, both mainly for Brian. One, you've mentioned that you don't have much of a social media presence or any way to really show case your work. While a lot of people do turn to Facebook, Instagram, etc. for this... I wonder if maybe simply an account on SimpleCove.com (Sean's website) might be a good fit? Two... work bench. Lots of questions - what style are you planning (Roubo, Nicholson, Moravian, Shaker, hybrid, something else?), size, what kind of wood are you thinking of using - fancy with hardwoods, or something simpler ala Siemensen's Naked Woodworker bench or Schwarz's Anarchist Workbench (both 2x construction lumber)? I think you'd mentioned still being up in the air about vise hardware - are you leaning towards wood screws like Lake Erie Toolworks, or metal like Benchcrafted? Maybe Hovarter, which has some quick-release options? And then the really big question... dog holes. Round or square? Answer carefully ;) I'm one of those people who has to fight the urge to build almost every bench design I see. Started with a Nicholson, but kind of went off in a weird direction with it and didn't like how it turned out. Deconstructed it and re-purposed most of the lumber for other projects. Couldn't make up my mind what I wanted to build next (not enough room for one of each!) so I put some inexpensive import (Yost) vises on a utility bench in the shop, and have been living with that for now. Not ideal, but it's letting me work out a few ideas on a trial basis before I have to commit. Very much looking forward to hearing (or seeing) more about your bench project! - Monte

Thank you all for spreading the knowledge and answering questions. I find myself building more cabinets lately out of plywood and I'm edge banding them with solid lumber (I go with 5/16 on the banding). I cut the banding a little wider than the sheet goods, glue it on and then trim it flush. I'm running into some issues during the trimming that I'm hoping you guys can chime in on. Often times, when I'm trimming the banding I get a little gouge here and there on the face veneer. It's not a huge deal on paint grade stuff but when I'm using something like walnut, cherry or white oak ply, it becomes a problem. What tips do you have for trimming the edge banding cleanly and efficiently without damaging the veneer? Below are some things I've tried and some of my experiences with these methods. I'm curious if you have other methods, or if you have some tips to improve what I'm already doing. Things I've tried so far: - Router balanced on the edge - so far the worst method. Too tippy and additional supports can take a while to set up, with ocasional slipups still. - Router jig - I saw Fredie @periodcraftsmen share a jig for flush triming the edge banding and I copied it. The jig has a flat wide reference face that rides on the panel face (laid flat) and it has a 90 degree fence that holds up a trim router horizontally. Using a downcut bit, the router is adjusted so that the bit is almost flush to the reference face and it trims the edgebanding protruding above the flat face. I hope you can picture that. This gives good results but I ocasionally run into issues at the start and end of the panel where the jig may want to tip a bit and bite into the face. - Tall fence on the table saw - using it kind of like an L-fence, the sacrificial face is set up above the blade and flush with the outer teeth. The panel rides the fence vertically and the edgbanding rides under the fence where it gets trimmed off. This so far gives the best results especially when I went to an extra tall fence to give it more of a bearing surface and not let the panel tip. Ocasionally the panel is a bit bowed which gives it a bit of trouble and it can be a bit unwieldy if the panel is large. Can be hard to keep it flat on a long panel. It is fast though. - Hand plane - using a block plane carefully work it down. I have still bit into it a few times when not careful but this is overall the most accurate method. It is slow though and can be a pain if there is a lot of trimming. - Bojan

Huy's Questions:

When you're building a piece of furniture (like a dresser), do you follow a specific order? Like cutting everything first, arming (make sure that everything works), disarming. Karel

I love your podcast. You try hard to fully answer questions asked and not provide flippant answers like other shows do. That’s what makes this show great. Now to my question. I have been wanting to upgrade my sanding game. I want to reduce the vibration, have it stop quickly, and produce a great result. I would love to hear your thoughts on what you look for in sanders such as the size (5 or 6 in), pad types (soft through hard), brands you have used and liked, and what brand of paper you buy. I’m starting to realize no one sander does it all anymore, so do you have a progression of sander purchases you would make for a simple furniture maker? Thanks you for anything you provide. - Brian Russell